Непоседа Заглушка4 Заглушка5

Excellent International Standards Advice? Tip#28

Новичок
FrankJScott
Сообщений: 91
20 дней назад
Little Craft Electrical Systems- Alternating And Immediate Current Installations
Small craft Electrical systems- Alternating and direct current installations (ISO 13297:2020) EN ISO 13297:2021
Electrical systems, as well as the introduction of innovative engineering in them, is a rather complex idea and has a number of certain subcategories and special gear. It's for each of the categories that different international standards are made, among which will be EN ISO 13297: 2021. This document defines the requirements for the layout, construction and installation of the following Kinds of DC and AC electrical systems, installed on small craft either separately or in combination:

A) extra-low-voltage direct current (DC) electrical systems which operate at nominal potentials of 50 V DC or less;
B) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding AC 250 V.

This document Doesn't cover the following:
-- electric propulsion systems of direct present less than 1 500 V DC, single-phase alternating up to 1 000 V AC, and three-phase alternating up to 1 000 V AC, that can be addressed by ISO 16315;
-- any conductor That's part of an outboard engine meeting and That Doesn't extend beyond the outboard engine manufacturers supplied cowling;
-- three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are addressed by IEC 60092-507. Amendments about which areas are not regulated by this standard make it possible to understand which equipment used in manufacturing can be regulated in accordance with this document, and not. If you're interested in familiarize yourself using more detailed characteristics of the standard, you can follow the link to your own site.

Small craft Waste systems Part 2: Sewage treatment systems (ISO 8099-2:2020) EN ISO 8099-2:2021
Despite the fact that most global standards are mostly associated with more international companies, corporations and global activities, they're also created for small and midsize companies, describing each distinct category and particular type of equipment. This document specifies requirements for the layout, installation and construction of sewage treatment systems on small craft. t doesn't address waste retention systems, nor accidental discharge avoidance of pollutants (e.g. petroleum, gas ) overboard. To start with, this global standard can be perceived as global for a certain type of activity. However, it needs to be noted that it's accommodated to the European Union marketplace and excludes some points which are necessary for a more international scale.

Metallic tube connections for fluid power and general use- Test methods for hydraulic fluid power connections ISO 19879:2021 EN ISO 19879:2021
The evaluation methods used for metal structures and goods are one of the most critical stages, since the wrong approach in this specific category of activity can entail substantial negative consequences from the financial aspect. That's precisely why one should clearly adhere to the recommendations specified in such international files as EN ISO 19879: 2021.

This record specifies uniform procedures for the testing and performance analysis of metallic tube links, stud ends for vents and flange connections for use in hydraulic fluid power applications. This document does not apply to the testing of hydraulic quick-action couplings, which is covered by ISO 18869. Tests outlined within this document are independent of each other and document the method to follow for each test. See the right component International Standard for signs of which tests to run and for performance standards. For eligibility of the connector, the minimal number of samples given in this document is tested, unless otherwise specified in the relevant connector standard or as agreed upon by the producer and the user. To create a certain system, it's essential not only to have qualified workers, but also to get an proper technological and scientific foundation, which will allow you to create an organization with transparent and well-established interaction between departments, and will also permit you to acquire the ultimate high results result in the form of a finished product or service in demand.

New ways for increasing the productivity of results
Electrical mechanical methods are one of the most commonly regulated by global standards. If in the previous stages of your activity you didn't think about acquiring global standards, this point can turn into a new level of development for your organization, moreover, you can make sure in a practical way that the introduction of this special kind of files permits you to minimize both physical and fiscal risks, bringing your organization to new qualitative levels of development. If in this list of criteria you have not found a proper one especially for your activity, but applicable in some category, you can visit our website and familiarize yourself with all the available standards. After all, it's there that it is possible to find the document that will become the beginning of a new way of developing your enterprise.
|
Перейти на форум:
Быстрый ответ
У вас нет прав, чтобы писать на форуме.